View previous topic :: View next topic |
Author |
Message |
Firstymer
Joined: 14 Jan 2008 Posts: 9 Location:
|
Posted: Tue Jan 15, 2008 2:25 pm Post subject: How to fix my temp. gauge??? |
|
|
I find it hard to believe that I cannot determine the temperature of my car engine because the temperature gauge on the dash does not work. So I need to know how to fix the problem that exist. Do anyone have an idea of the procedure and what part(s) I need?
00' GP SE v6 3.1L Vin "J"
122570+KM _________________ |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Larry Site Admin
![](images/avatars/980863097447eed2cb09ef.jpg)
Joined: 01 Jun 2006 Posts: 4774
|
Posted: Wed Jan 16, 2008 9:19 pm Post subject: Temp Gauge |
|
|
It is pretty rare that a gauge actually ceases to function. It is uaually the sending unit. But first be sure to check the connections.
That being said, if this is an '00 model, there are other factors that could be at play here, being a "computer car".
Have you had a diagnostic run (ie: hooked up to a computer) to see if a code is shown?
Let us know what has been done so far to try to isolate the problem. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Firstymer
Joined: 14 Jan 2008 Posts: 9 Location:
|
Posted: Thu Jan 17, 2008 11:08 am Post subject: |
|
|
Thanks for the reply, well nothing hasn't been done to isolate the problem. However, I received the code P0650-MIL Control Circuit Malfunction
MIL is Malfunction Indicator Lamp meaning the SES/CEL light circuits. but to my knowledge only ABS light remains on while car is on. I was told it could be the coolant sensor. _________________ |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Larry Site Admin
![](images/avatars/980863097447eed2cb09ef.jpg)
Joined: 01 Jun 2006 Posts: 4774
|
Posted: Thu Jan 17, 2008 12:27 pm Post subject: Temp Question |
|
|
I would suggest trying to replace the coolant sensor as I mentioned at first ("sending unit"). They are usually the problem. Try starting with the simplest item before thinking about tearing into the more complicated things.
Let us know what you do as you chase this problem. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Firstymer
Joined: 14 Jan 2008 Posts: 9 Location:
|
Posted: Thu Jan 17, 2008 2:10 pm Post subject: |
|
|
Where can I find the coolant sensor on the engine and how can I go about replacing it? Do you have any detail photo of the engine component? _________________ |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Firstymer
Joined: 14 Jan 2008 Posts: 9 Location:
|
Posted: Fri Jan 18, 2008 2:35 pm Post subject: |
|
|
Yeah whats up with the picture...that supposed to be a joke...do you have any description on what the coolant sensor look like and where it can be found on the engine? _________________ |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Firstymer
Joined: 14 Jan 2008 Posts: 9 Location:
|
Posted: Fri Jan 18, 2008 5:37 pm Post subject: |
|
|
Yeah I notice some Coolant loss in the resvoir but not leaking onto the floor. _________________ |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Larry Site Admin
![](images/avatars/980863097447eed2cb09ef.jpg)
Joined: 01 Jun 2006 Posts: 4774
|
Posted: Sun Jan 20, 2008 7:04 pm Post subject: Sensor Location |
|
|
I have been doing some checking and the closest I can find (for now) is some GP info from a 1985 manual. It is for the 3.8 V-6 engine.
One point they make about the gage is to be certain that all contacts are clean and tight at the gage. They also mention a good ground at the gage.
Attached is a drawing showing the sensor location on the 3.8. It may be the same as your 3.1. If not, it should still help you in identifying the sending unit (sending unit, sensor, switch... all the same, just called differently). |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Firstymer
Joined: 14 Jan 2008 Posts: 9 Location:
|
Posted: Tue Jan 22, 2008 9:21 am Post subject: |
|
|
Thanks for the pic...I will make certain I look under the hood today! Do you have the procedure in replacing it? _________________ |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Larry Site Admin
![](images/avatars/980863097447eed2cb09ef.jpg)
Joined: 01 Jun 2006 Posts: 4774
|
Posted: Tue Jan 22, 2008 1:24 pm Post subject: Sensor Replacement |
|
|
They simply unscrew and screw in a new one. Just a big pipe thread. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Firstymer
Joined: 14 Jan 2008 Posts: 9 Location:
|
Posted: Tue Jan 22, 2008 1:41 pm Post subject: |
|
|
Thanks for the reply! I was told before that coolant may pour out when unscrew. _________________ |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Larry Site Admin
![](images/avatars/980863097447eed2cb09ef.jpg)
Joined: 01 Jun 2006 Posts: 4774
|
Posted: Tue Jan 22, 2008 6:04 pm Post subject: Sensor Replacement |
|
|
If you are wondering if you have the right sensor, the flood of coolant would actually be a good sign. Oil= not good! Coolant= good.
It would, of course, be a good idea to drain the radiator at least down to the level of the sensor location. Be sure to do when cool. |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
Firstymer
Joined: 14 Jan 2008 Posts: 9 Location:
|
Posted: Wed Jan 23, 2008 9:16 am Post subject: |
|
|
Alright thank...I'll make certain! _________________ |
|
Back to top |
|
![](templates/subSilver/images/spacer.gif) |
|